Best Manufacturer, Suppliers & Exporters of High Quality Laboratory Kjeldahl Instruments

Water Distillation

₹100,000.00

This has been designed for better and accurate control of the distillation unit. It has been incorporated with advanced microcontroller based electronic circuitry, which gives and easy user machine interaction. The alpha numeric LCD which has been used shows all messages that correspond to the running of the machine.

Environment friendly & suitability
One Touch Use, Fully Automatic ,
Intelligent, dual stage all glass type
Fully automatic control save energy & money– By setting the required output volume in litters. Aer completion of the process heater is turned off and the cooling water inlet is closed automatically.
Boiler empty detection intelligence built in– when the water level inside the boiler drops below the heater, boiler empty condition is detected.
Gate Valve to one side - Conserves cooling water wastage in case of power failure
Flow switch - In built safety feature for the equipment unit shut off in case of cooling water failure. When the inlet water flow to the unit is low, this error is displayed with buzzer indication. The process in paused until the inlet flow is resumed.
Easy to read Alpha numeric LCD and keypad for all settings and messages that correspond to the running of the machine.
Auto cleaning detection
Probe error detection
So Calibration of output volume to compensate seasonal temperature and flow rate changes
Manual overriding flow sensor and Gate (solenoid) valve
Serviceability Replaceable Silica sheathed (Quartz) Heater
Safety of user & instrument against wattage/power variation

Technical Specification:

Model No.	DN.WD.01	DN.WD.01
Output Cap. (approx.)	2 ltrs/hr	4 ltrs/hr
Stage	Double Stage	Double Stage
Cooling water requirement (approx.)	2 ltr/min	2-4 ltr/min
Conductivity uS/cm	0.8-1.0	0.8-1.0
Power Rating (Total)	3.0KW	6.0KW
AC Voltage	220-240VAC	220-240VAC
AC Frequency	50-60Hz	50-60Hz

View Cart

Select options / Details Quick View

Water Bath Cum Water Bath Shaker (touch Screen Version)

₹100,000.00

Safety Features

Water bath and shaker in a single system.
Selection of mode in the touch screen
Absolutely noiseless operation.
Programmable system
Removable tray
Flexible Polyproplene Rubber Clamps reinforced with inner metallic cup for sturdy & rugged use for intact grip to perfectly hold the flask

Technical Specification:

Model	1855.DNEU.01
Operation	Water bath or water bath shaker
Material of construction	MS with powder coated finish
Type of motion	Reciprocal motion
SPM range	50 to 150 Strokes per minute
Movement	Linear link guided drive mechanism
Movement sensor	IR scan sensor
Motor	Stepper servo motor (Brushless)
Drive	Servo drive
Process controller	4.3” TFT touch screen controller
Display	Feather touch membrane key pad with touch controller (Power, Heater)
Temperature controller	PID controller
Temperature range	5 Degree above ambient to 100 Degree
Temperature accuracy	+/- 0.5Degree
Temperature sensor	Pt 100
No of program	1 program, 5 steps for both shaker and water bath
Programmable	For Strokes Per M inute, Temperature and Time
Heater	Immersion Heater
Heater power	1500 W
Water tank	Stainless steel
Tank capacity	15 lit
Tray	Stainless steel, Removable
Tray capacity	250ml clamp-9 nos
Hood or cover	Stainless steel
Internal Recirculation pump for Temperature stability	Magnetic pump
External recirculation pump	(optional) magnetic pump
Electrical requirement	230V/50Hz/ 6A
Unit dimension	25 x 25 x15inches

View Cart

Select options / Details Quick View

Three in One Nitrogen Analyser – Kjeldahl

₹1,000,000.00

Three in One Combo Automatic 6 Place Digestion With Distillation & Scrubber With Common Touch Screen Control & Display

The control panel unit along with inbuilt temperature controller, timer, mother board and SMPS is be isolated in separate control tower and housing to protect electronics from wet chemistry & acid/ alkali process area for longevity and safety of all electronic components.
Water in the scrubber tank is drained and filled automatically every time at the end of digestion thereby draining the water for every consecutive cycle.
Manual drain of water from the scrubber tank is also provided.
A separate distilled water line to the steam generator.
Auto refilling of distilled water to the steam generator is provided by using a proximity sensor.
Monitoring of boiler water level from outside.
Users choice to choose independent or combined operation of digestion and distillation.
Inbuilt safety from Over voltage

Technical Specification:

Model	:	DN.NA.01
Material of construction	:	MS with powder coated ﬁnish
Operations	:	Digestion, Distillation and Scrubb
Cooling System & Automatic	:	Through water coil condenser in higher models
No of samples	:	6 nos
Tube dimension	:	42 x 300mm
Tube capacity	:	250ml (Borosilicate Glass 3.3)
Process controller	:	4.3” TFT touch screen controller
Mode of operation	:	Auto and Manual
Digestion Heating block	:	Extruded Aluminium block HE 30 Grade 6063 for 6 samples
Digestion Heater	:	Casted Aluminium alloy heater IS 4159
Digestion Heater wattage	:	1500 W
Digestion Temperature controller	:	PID controller
Digestion Temperature Range	:	50 degree to 450 degree
Digestion temperature accuracy	:	+/- 1%
Digestion temperature sensor	:	Chromal K type thermocouple upto 1200°C
Digestion program	:	5 program and 5 steps
Digestion program parameter	:	Temperature and time
Digestion block insulation	:	Ceramic wool
Digestion acid fumes removal	:	Teﬂon adaptor fuse to manifold using & outlet connected to the glass suction pump
Handle	:	Polyamide
Two tier console	:	To place Insert rack and Manifold Rack
Digestion tube insert Rack	:	Stainless steel-SS304 with Glossy Finish
Digestion Manifold Rack	:	Stainless steel-SS304 with Glossy Finish
Digestion Drip Tray	:	Stainless steel-SS304 with Glossy Finish
Exhaust fume condensation	:	In water
Scrubber tank	:	Stainless Steel 304
Scrubber water leveller	:	Float switch
Scrubber tank capacity	:	10 litre
Scrubber suction pump	:	Giant ﬁlter pump
Distillation expansion vessel	:	Glass vessel with Teﬂon insert for alkali addition inlets nippons for alkali addition and steam addition
Scrubber water re-circulation pump	:	2 Magnetic pump with ﬂow rate of 18L/min
Scrubbing Tubing Hardness	:	Silicone tube 70±5 shore A, Temp. resistance -60°C to +200°C
Real time monitoring of process	:	yes
No of distillation	:	One at a time
Distillation programme	:	5 program/3 steps
Distillation Programme steps	:	Alkali, reaction delay and Process
Distillation Dosing pump	:	For alkali addition 24 DC Motor 500 ml/min
Distillation steam Generator	:	Stainless steel-SS304 with pressure release valve to back suction of sample
Distillation water condenser	:	Glass with 2 bulb and coil condenser
Distillation solenoid valves	:	For Steam, Reﬁlling and Vent
Distillation Heater	:	Immersion Heater
Distillation Heater Wattage	:	1500 W
Distilled water tank	:	PVC
Distilled water tank capacity	:	5 Lit
Distillation Reagent tank	:	PVC
Distillation Reagent tank capacity	:	2 lit
Electrical requirement	:	230v/50Hz/16A
Unit Dimension	:	32 x 26 x 41 inches
Connectivity to printer	:	Available for higher models
Connectivity to USB	:	Available for higher models
Real Time Monitoring of Process	:	Yes
Nitrogen recovery	:	99.5%
Nitrogen reproductiobility	:	+/-1%
RSD	:	<1%
LOD	:	1-200 mg with >_0.1mg of Nitrogen
Total Time process	:	2.5 Hours

View Cart

Select options / Details Quick View

Hot Air Oven Cum Incubator

₹100,000.00

Use as a Incubator or Hot air oven
Forced air circulation by convection
Shelf Height adjustable to 7 levels
Curved edges at the four corners for easy cleaning.
See Through window for viewing samples
Automatic cut off of Heater and blower when the door is opened.
Sturdy SS handle with chrome finish
Additional port for cross checking the temperature of the chamber.
Over voltage protection

Technical Specification:

Material of construction	Outer MS with powder coated finish and Inner stainless steel
Capacity	91 lit
Dual Mode Operation (2 in 1)	Hot air Oven Mode or Incubator Mode
Inner dimension	450 x 450 x 450 mm
Outer dimension	560 x 610 x 680mm
Process controller	4.3” TFT Touch screen controller
Display	Feather touch membrane key pad with touch screen. (Power, Oven, Incubator, heater)
Temperature controller	HMI
Temperature Range	5 degree above ambient to 200 degree
Temperature accuracy	At 120Degree-+/- 1%, At 37 Degree- +/- 0.1 Degree
Temperature sensor	PT 100
Number of program	5
Number of steps	5
Programmable for	Temperature and time
Heater	Strip Heater
Heater wattage	Oven-1625 W and Incubator-325 W
No of Trays	2
Chamber insulation	Ceramic wool
Over temperature protection	Using thermostat
Electrical requirement	230v/50Hz/10A

View Cart

Select options / Details Quick View

COD Digestion System

₹100,000.00

Stainless steel Insert rack to handle COD digestion tubes.
MS rack to keep Air condensers.
MS rack with hole to place insert rack with tubes for adding reagents in water.
Stainless steel water tank

Technical Specification

Model	DEN.N15CT.01 (TOUCH SCREEN CONTROLLER)
No of samples	15
Tube dimension	36 x 200 mm
Tube capacity	150ml
Tube material	Glass with ground joint
Reflux condenser	Air condenser with ground joint
Reflux condenser dimension	640mm
Heating block	Extruded Aluminium block
Well depth	90mm
Material of construction of housing	MS with powder coated finish
Heater	Casted Aluminium alloy Heater
Heater wattage	2000 W
Temperature controller	PID controller
Process controller	4.3” TFT with touch screen
Temperature range	50 degree to 300 degree
Temperature accuracy	+/- 1%
Temperature sensor	K type thermocouple
Block insulation	Ceramic wool
No of Programs	5 program
No of steps	5 steps
Type of program	Time and Temperature
Feature touch membrane key pad	Power and Heater
Over voltage protection	By circuit breaker
Electrical requirement	230V/50Hz/10A
Unit dimension	56 x 14 x 36 Inches (L x B x H)

View Cart

Select options / Details Quick View

Automatic Solvent / Fat Extraction System

₹100,000.00

Safety Features Standalone housing for Temperature controller to protect electronics from solvent area & heat zone. PC chart software performs Live graphical representation of time/temperature gradient on PC Connectivity

Auto Alarm for recovery phase
Auto power off mode on completion of extraction.
Independent loading of sample with individual mechanical controls.
Inbuilt safety features like auto error indication, auto over temperature protection and auto sensor break protection.
Cold water line for condensation of solvent with silicon hose interconnection for condensor

Technical Specification:

MODEL	PL -S6-R
Description	Automatic PC Compatible Auto sequencing Regular Six Place Solvent Extraction System
No. of Positions	Six Samples
Sample Size	0.1 to 8 gms (depending on the type of sample)
Temperature Control Range	35°C (Ambient) to 300°C
Digital Timer	Range : 0-99.59 hrs (Settable in hrs, min and seconds), Digital display of set time and actual time (1-5999 minutes) , Modes of operation: heater cut off mode & alarm mode
Temperature Accuracy / Precision	± 0.5° C
Ramp & Hold	Integrated Auto Sequencing programs with 12 desirable sequence ramp / steps of time and temp. domain for each programme.
Presets	Select able Programs(Customizable): Integrated Auto Sequencing Features with 30 intelligent memory programs
Heater Source	Casted Aluminium Alloy Heaters
PID Control	Fuzzy logic Microprocessor based PID Controller with Auto tuning facility.
Temperature Setting	Feather touch membrane keys
PC & Printer Connectivity	Direct USB port for PC/Laptop connectivity Intelligent Software for PC compatibility for 2 way Bidirectional communication
Display	Bright Digital two line Alphanumeric LCD Digital Display of time and temperature
Extraction Thimbles	* Thick Nitrocellulose thimble (f25mm X 80mm) - 1 Box of 25 Nos. * Highly versatile to accommodate 2 sizes of Thimbles. Optional Macro Thimbles of size (33 mm dia x 80mm L) compatible in the system.
Power Consumption	2000 Watts.

View Cart

Select options / Details Quick View

Automatic Fibre Estimation System – (6 Place) Auto-Sequencing

₹100,000.00

Designed to protect electronics from acid / alkali wet area & heat zone
Independent loading of sample with individual mechanical controls
Auto acoustic alarm on completion of process
Auto power off mode on completion of process
Inbuilt safety features like auto error indication, auto over temperature protection and auto sensor break protection
PC chart Software Performs Live Graphical Representation of Time/ Temperature Gradient on PC Connectivity

Technical Specification:

Description	Automatic Six Place PC Compatible Autosequencing Regular Version Fibre Estimation System
Display	Bright Digital two line Alphanumeric LCD Digital Display of time and temp.
No. of Positions	Six Samples
Sample Size	0.1 to 4 gms (depending on the type of sample)
Temperature Control Range	RT- 500º C (Continuously variable)
Digital Timer	0-99.59 hrs (Settable in hrs, min and seconds), Digital display of set time and actual time (1-5999 minutes) , Modes of operation: heater cut off mode & alarm mode
Temperature Accuracy / Precision	± 0.5° C
Ramp & Hold	Integrated Auto Sequencing programs with 12 desirable sequence ramp / steps of time and temp. domain for each programme
Presets	Selectable Programs(Customizable): Integrated Auto Sequencing Features with 30 intelligent memory programs
Heater Source	Ceramic Infrared Heater
PID Control	Fuzzy logic Microprocessor based PID Controller with Auto tuning facility
Temperature Setting	Feather touch membrane keys
Crucibles	Sintered Silica glass Crucible with P1 Porosity disc (6 Nos.)
Extractor	Marked borosilicate extraction vessel
Preheating Hotplate	Fibra Flow System with self priming pump connected to water suction filter pump.
Power Consumption	2500 Watts.
PC & Printer Connectivity	Direct USB port for PC/Laptop connectivity Intelligent Soware for PC compatibility for 2 way Bidirectional communication